Perencanaan Loading Frame Menggunakan Material Baja Wind Cathcer Gedung A, Institut Teknologi Kalimantan
Abstract
The function of the wind catcher structure located in building A of Kalimantan Institute of Technology is no longer felt by building users. The construction causes leakage because it is located in the hallway of building A and is not covered by anything. This research was conducted to utilize and create a design of a fixed loading frame tool where the Integrated Laboratory 2 of the Kalimantan Institute of Technology requires the tool to support the research activities of students and outsiders. The method used in the research is the laboratory experimental method to determine the mechanical properties of the wind catcher structure steel material and the numerical method, namely ASD (Allowable Strength Design) to process, design and model the fixed loading frame tool. The results of the material tensile test test obtained a value of fy of 398 Mpa and fu of 514 Mpa, the dimensions of the frame are 4.55 x 2.95 m, the load model applied is one point and two point load. Modeling is done by trial and error load values and obtained load values in accordance with the capacity of the available profile frame, namely WF 300 x 150 x 6 x 9 can withstand loads of 200 kN and modeling in accordance with the design criteria load (1000 kN) the profile on the beam can be changed to WF 588 x 300 x 18 x 20 and on the column profile changed to WF 450 x 300 x 11 x 18. The results of modeling a loading frame made of wind catcher structural profiles have met the design criteria parameters made by adding beams vertically in the x-axis beam (longitudinal) located at the center of the frame (vertical double beam design).
Keywords
Full Text:
PDFReferences
Akbar, F., 2018. Behaviour Of Concrete Beam Repaired Using Patch Mortar And Straight Strengthening Rebar. Brawijaya University.
American Society for Testing and Materials, 2013. ASTM E8: standard test methods for tension testing of metallic materials. West Conshohocken: ASTM.
Ananta, B.D. and Apriyatno, H., 2022. Eksperimen Kuat Lekat Chemical Angkur Deform Kedalaman 110 mm Metode Cast-In Place dan Post-Installed Drill Bit Extractor. Jurnal Ilmiah Multidisiplin Indonesia, 2(3), pp.543-550.
Budiman, H., 2016. Analisis pengujian tarik (tensile test) pada baja st37 dengan alat bantu ukur load cell. J-ENSITEC, 3(01).
Dady, Y.T., Sumajouw, M.D. and Windah, R.S., 2015. Pengaruh kuat tekan terhadap kuat lentur balok beton bertulang. Jurnal Sipil Statik, 3(5).
Dewobroto, W., 2016. Struktur Baja Perilaku, Analisis & Desain–AISC 2010 Edisi ke-2. Tanggerang: Penerbit Jurusan Teknik Sipil UPH.
Fatriady, M.R., 2016. Studi Beban Fatik Terhadap Kapasitas Lentur Balok Beton Bertulang Perkuatan Glass Fiber Reinforced Polymer Sheet. Journal Techno Entrepreneur Acta, 1(1).
Fisher, James dan Kloiber, Lawrence., 2006. Design Guide 2nd Edition Base Plate and Anchor Rod Design. American Institute of Steel Construction.
Ginting, A., 2007. Kajian balok beton Styrofoam ringan dengan tulangan menyebar. Jurnal Teknik Sipil, 3(2), pp.127-140.
Ginting, A., 2008. Kajian Sambungan Lewatan Jenis Contact Lap Splice pada Beton Bertulang. Jurnal Teknik Sipil, 4(2), pp.105-114.
Huda, A. and Apriyatno, H., 2020. Eksperimen Tarik Angkur Tipe Ekspansi secara Cast in Place dan Postinstalled dengan Keggalan Breakout Concrete. Seminar Nasional Teknik Sipil X 2020.
Indryawan, H.K. and Apriyatno, H., 2020. Perilaku Kegagalan Breakout terhadap Gaya Geser pada Baut Angkur terhadap Perbandingan Kekuatan Metode Pemasangan Castin Place dan Post Installed. Seminar Nasional Teknik Sipil X 2020.
Megasari, S.W., 2014. Perkuatan Geser Pada Kolom Beton Bertulang Berpenampang Persegi Dengan Metoda Concrete Jacketing. Jurnal Saintis, 13(1).
Mourad, A.H.I. and Alnaqbi, A.H., United Arab Emirates University, 2018. Load frame testing device adapted to test different environmental conditions. U.S. Patent 10,132,731.
Olii, M., Handono, B.D. and Pandaleke, R.E., 2018. Studi Numerik Perilaku Sambungan Pelat Dasar Kolom (Column Base Plate). Jurnal Sipil Statik, 6(12).
Pangau, G.Y., Pandaleke, R. and Handono, B.D., 2016. Analisis Dimensi Pelat Dasar (Base Plate) Pada Kolom Struktur Baja Yang Mampu Tahan Terhadap Efek Pray. Jurnal Sipil Statik, 4(6).
Prameswari, B., 2008. Studi Efektifitas Lapis.
Priyanda, A., 2019. Analisis Kapasitas Beban Kerja Struktur Loading Frame 3D Dengan Metoda Desain Kekuatan Izin Berdasarkan SNI 1729-2015 (Studi kasus: Loading Frame Laboratorium Struktur dan Mekanika Rekayasa Universitas Islam Indonesia, Yogyakarta) (Doctoral dissertation, Universitas Islam Indonesia).
Rahman, M.P. and Kurniawan, F.A., 2022. Analisa Kekuatan Material Bahan Carbon Steel AISI 1018 Dan Baja Tulangan Polos SNI P40 Sebagai Angkur Pada Tower Dengan Metode Uji Tarik. Buletin Utama Teknik, 17(3), pp.291-301.
Salindeho, R.D., Soukotta, J. and Poeng, R., 2013. Pemodelan pengujian tarik untuk menganalisis sifat mekanik material. Jurnal Poros Teknik Sipil UNSRAT, 2(2).
Setiawan, A., Idris, S. and Sanggau, P.P.N.P., 2020. Analisis Sifat Mekanik Baja Ulir Berdasarkan Diamter. Suara Teknik: Jurnal Ilmiah, 11(2), pp.70-78.
Silviana, M., 2017. Studi Kekuatan Sambungan Batang Tarik Pelat Baja Dengan Alat Sambung Baut. Jurnal Inotera, 2(2).
Siregar, D.S., Panjaitan, S. and Simbolon, R.H., 2020. Analisa Pengaku (Stiffener) pada Balok Baja Iwf Akibat Torsional Buckling. Buletin Utama Teknik, 15(2), pp.121-129.
Suhardiman, M., Ginting, A. and Herman, H., 2011. Pengaruh Jarak Antara Elemen Batang Tekan Ganda Terhadap Kuat Tekan. Jurnal Teknik Sipil, 7(1), pp.1-14.
Takada, S. and Furuya, K., Saginomiya Seisakusho Inc, 2005. Load test machine. U.S. Patent 6,938,494.
DOI: https://doi.org/10.35334/be.v8i2.5648
Copyright (c) 2024 Borneo Engineering : Jurnal Teknik Sipil
![Creative Commons License](http://licensebuttons.net/l/by-sa/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Published By : Civil Engineering Department, Faculty of Engineering, University of Borneo Tarakan Jl. Amal Lama No 1, Tarakan 77115, Indonesia | All publications by Borneo Engineering: Jurnal Teknik Sipil are licensed under a |
Borneo Engineering Indexed By: